Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 173 | Manualshive

Page: 173 / 264

background image

8. Connect the new front system fan cable to the 4-pin system fan 1 connector on the system board.

See “System board components” on page 45.

Note:

For server models with five to eight 3.5-inch hot-swap hard disk drives, there is a secondary front

system fan installed in the front system fan 2 mounting area (above the front system fan 1 mounting
area). The cable of the secondary front system fan is connected to the 5-pin system fan 2 connector on
the system board. See “System board components” on page 45.

9. If you are instructed to return the old front system fan, follow all packaging instructions and use any

packaging materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the replacement, go to “Completing the parts replacement” on page 177.

Replacing the rear system fan

Attention:

Do not open your server or attempt any repair before reading and understanding the “Safety information”

on page iii and “Guidelines” on page 85.

This topic provides instructions on how to replace the rear system fan.

CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Note:

Depending on the model, your server might look slightly different from the illustrations in this topic.

To replace the rear system fan, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. Remove the server cover. See “Removing the server cover” on page 87.

3. Locate the rear system fan. See “Server components” on page 25.

4. Disconnect the rear system fan cable from the system fan 3 connector on the system board. See

“System board components” on page 45.

Chapter 6

.

Installing, removing, or replacing hardware

161

«
...
171
172
173
174
175
...
»

Summary of Contents for ThinkServer TS430









































































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TS430

Brand: Bartlett Pages: 30

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: tams elektronik Pages: 12

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: Apricus Pages: 32

Brand: TUYA Pages: 28

MultiLoad II EXL

Brand: Toptech Pages: 83

Brand: Comparato Pages: 20

Brand: A10 Networks Pages: 2

Brand: Z-Wave Pages: 5

Brand: Nordson Pages: 20

Brand: UUGear Pages: 38

DIGI-STAR GT400

Brand: AGRI TRONIX Pages: 26

DAQP-CHARGE-B Series

Brand: Dewetron Pages: 14

PHAZR-5 UR5U-9000

Brand: Universal Remote Control Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands