Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 171 | Manualshive

Page: 171 / 264

background image

Depending on the model, your server might come with one or two front system fans. See “Server
components” on page 25 to locate the front system fan(s) installed in your server model.

Note:

The front system fan 2 is only available in server models with five to eight 3.5-inch hot-swap hard disk

drives installed. The front system fan 2 should only be factory-installed. Lenovo does not support users
and servicers to install a secondary front system fan by themselves.

CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Note:

Depending on the model, your server might look slightly different from the illustrations in this topic.

To replace the front system fan, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. Remove the server cover. See “Removing the server cover” on page 87.

3. Locate the front system fan 1. See “Server components” on page 25.

4. Disconnect the front system fan 1 cable from the 4-pin system fan 1 connector on the system board.

See “System board components” on page 45.

Chapter 6

.

Installing, removing, or replacing hardware

159

«
...
169
170
171
172
173
...
»

Summary of Contents for ThinkServer TS430









































































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TS430

Brand: FAAC Pages: 12

Brand: Keba Pages: 16

Brand: KEB Pages: 16

Brand: Parker Pages: 54

Brand: RAM Pages: 71

Micro850 series

Brand: Allen-Bradley Pages: 24

Brand: Lauda Pages: 40

RSF B mini Series

Brand: Harmonic Drive Pages: 33

Brand: ENTRYPASS Pages: 42

Brand: FUTABA Pages: 16

Multilin GEK-113328A

Brand: GE Pages: 218

Brand: C-TEC Pages: 42

Brand: Satel Pages: 48

Brand: Italtecnica Pages: 16

Brand: KAT Percussion Pages: 24

Brand: Acconeer Pages: 15

Brand: Hanbay Pages: 13

Brand: Zehnder Pumpen Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands