Lenovo ThinkServer TS430 Hardware Maintenance Manual Download Page 196 | Manualshive

Page: 196 / 264

background image

Symptom

Action

5. Replace the optical drive.

6. (Trained service technician only) Replace the system

board.

A disc is not working correctly.

1. Make sure that the disc is in the optical drive with the

shiny side facing down.

2. Make sure that the disc surface is clean and not

scratched.

3. Check the disc or package for regional coding. You

might need to purchase a disc with coding for the
region where you are using the product.

4. Restart the disc player program.

5. Restart the server.

6. Run any optical drive diagnostic programs if you

have.

7. Reinstall the optical drive and reconnect cables.

8. Replace the signal cable for the optical drive.

9. Replace the optical drive.

Hard-disk-drive problems

Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page
181 for the subsequent steps you should check after using the information in this topic. If the problem
cannot be solved by yourself, seek technical assistance. See Chapter 9 “Getting information, help, and
service” on page 227.

Notes:

1. If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6

“Installing, removing, or replacing hardware” on page 85.

2. If the server model comes with hot-swap hard disk drives, the status LEDs on each hot-swap hard disk

drive help you easily identify a problem. See “Hot-swap hard-disk-drive status LEDs” on page 32.

Symptom

Action

A newly installed non-hot-swap hard disk drive is not
recognized.

1. Make sure that:

• The signal cable and connector are not damaged.

• The non-hot-swap hard disk drive is securely

connected to the correct SATA connector on the
system board and the SATA connector is enabled
in the Setup Utility program. See “Using the Setup
Utility program” on page 57.

• All cables and jumpers (if any) are installed

correctly.

2. If you have any diagnostic programs, run the

diagnostic programs to test the hard disk drive.

3. Reinstall the non-hot-swap hard disk drive and

reconnect cables.

4. Replace the signal cable for the non-hot-swap hard

disk drive.

184

ThinkServer TS430 Hardware Maintenance Manual

«
...
194
195
196
197
198
...
»

Summary of Contents for ThinkServer TS430









































































































































































































































































Reviews:

No comments

Related manuals for ThinkServer TS430

Brand: KELCO Pages: 36

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Eaton Pages: 12

Brand: TCi Pages: 9

Brand: Panasonic Pages: 8

CPX-AP-A-16DI-D-M12-5P

Brand: Festo Pages: 16

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

LOWARA Aquavara IPC

Brand: Xylem Pages: 292

Brand: Samcen Pages: 65

Brand: Danfoss Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands