Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 136

Page: 136 / 170

8. Install the new power supply assembly into the chassis so that the screw holes in the new power supply

assembly are aligned with the corresponding holes in the rear of the chassis. Then, install the three
screws to secure the new power supply assembly in place.

Note:

Use only screws provided by Lenovo.

Figure 73. Installing the power supply assembly

9. Connect the new power supply assembly cables to all drives and the system board. See “Locating

parts on the system board” on page 79.

132

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands