Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 106

Page: 106 / 170

6. Slide the new hard disk drive into the hard disk drive bay and align the screw holes in the new hard

disk drive with the corresponding holes in the drive bay. Then, install the four screws to secure the
new hard disk drive in place.

Figure 33. Installing the hard disk drive

7. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an

available SATA connector on the system board. See “Locating parts on the system board” on page 72.
Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive.

Figure 34. Connecting a SATA hard disk drive

8. To complete the installation or replacement, go to “Completing the parts replacement” on page 112.

Replacing the front audio and USB assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

102

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands