Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download | Manualshive

Page: 134 / 170

background image

Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.

To replace the power supply assembly, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 117.

4. Pivot the drive bay assembly upward. Then, pivot the two plastic retaining clips outward to remove

the heat sink fan duct from the failing heat sink and fan assembly.

Figure 71. Removing the heat sink fan duct

5. Disconnect the power supply assembly cables from all drives and from the 24-pin power connector and

4-pin power connector on the system board. See “Locating parts on the system board” on page 79.

Note:

You might also need to release the power supply assembly cables from some cable clips or ties

that secure the cables to the chassis. Make sure that you note the cable routing before disconnecting
the cables.

130

ThinkCentre Hardware Maintenance Manual

«
...
132
133
134
135
136
...
»

Summary of Contents for ThinkCentre Edge 3484











































































































































































Reviews:

No comments

Related manuals for ThinkCentre Edge 3484

Brand: A1Touch Pages: 9

Brand: Medion Pages: 88

Brand: Compaq Pages: 222

Brand: Moxa Technologies Pages: 19

Compaq Presario,Presario 4103

Brand: Compaq Pages: 2

Brand: Supermicro Pages: 109

Brand: IBM Pages: 2

ThinkCentre 8143

Brand: IBM Pages: 34

Brand: IBM Pages: 2

Brand: IBM Pages: 32

Brand: IBM Pages: 59

Brand: IBM Pages: 24

Brand: IBM Pages: 91

Brand: IBM Pages: 108

Brand: IBM Pages: 74

545 Output Punch 1

Brand: IBM Pages: 50

92296GU - IntelliStation M - Pro 9229

Brand: IBM Pages: 86

Brand: IBM Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands