Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download | Manualshive

Page: 100 / 170

background image

CAUTION:

The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.

To replace the microprocessor, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. Lay the computer on its side for easier access to the system board.

4. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 92.

Note:

Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it

does not get in contact with anything.

5. Lift the small handle

1

and open the retainer

2

to access the microprocessor

3

.

Figure 27. Accessing the microprocessor

6. Lift the microprocessor straight up and out of the microprocessor socket.

96

ThinkCentre Hardware Maintenance Manual

«
...
98
99
100
101
102
...
»

Summary of Contents for ThinkCentre Edge 3484











































































































































































Reviews:

No comments

Related manuals for ThinkCentre Edge 3484

Brand: Barco Pages: 202

Brand: Gateway Pages: 182

Brand: Worx Professional Pages: 106

Brand: VisuNet Pages: 81

Brand: Aaeon Pages: 45

Brand: Montezuma Pages: 24

Brand: Alienware Pages: 55

Brand: Asus Pages: 54

Brand: Asus Pages: 48

Brand: Asus Pages: 80

Brand: Asus Pages: 66

Brand: Asus Pages: 92

Brand: Asus Pages: 48

Brand: Asus Pages: 82

Brand: Asus Pages: 46

Brand: Asus Pages: 80

Brand: Asus Pages: 81

Multimedia System S-presso

Brand: Asus Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands