Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download

Page: 90 / 170

• If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it

out of the slot.

Figure 15. Removing a PCI card

Notes:

a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small

amount until it is removed from the card slot.

b. If the card is held in place by a retaining latch, press the card retaining latch

as shown to

disengage the latch. Grasp the card and gently pull it out of the slot.

5. Remove the new PCI card from its static-protective package.

6. Install the new PCI card into the appropriate slot on the system board. See “Locating parts on the

system board” on page 72.

Note:

If you are installing a PCI Express x16 graphics card, make sure the memory slot retaining clips

are closed before you install the graphics card.

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands