Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 122

Page: 122 / 170

Figure 52. Reinstalling the front bezel

5. To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Accessing the system board components and drives

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

This section provides instructions on how to access the system board components and drives.

To access the system board components and drives, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 117.

4. Pivot the drive bay assembly upward to access all the internal drives, cables, and other components.

118

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands