Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 108 | Manualshive

Page: 108 / 170

background image

This section provides instructions on how to replace the WiFi units. The WiFi units include a WiFi adapter
card, a WiFi card module, and a rear WiFi antenna cable.

Replacing the WiFi units involves the following operations:

•

“Removing the WiFi adapter card” on page 104

•

“Removing the WiFi card module” on page 105

•

“Installing the WiFi units” on page 106

Removing the WiFi adapter card

To remove a WiFi adapter card, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. If your computer comes with a WiFi card module that supports the Bluetooth function, disconnect

the Bluetooth cable from the WiFi adapter card.

Figure 36. Disconnecting the Bluetooth cable

Note:

The Bluetooth cable connects the Bluetooth connector on the WiFi adapter card to the front USB

connector on the system board to support the Bluetooth function.

4. At the rear of the computer, remove the screw that secures the PCI card latch.

104

ThinkCentre Hardware Maintenance Manual

«
...
106
107
108
109
110
...
»

Summary of Contents for ThinkCentre Edge 3484











































































































































































Reviews:

No comments

Related manuals for ThinkCentre Edge 3484

Brand: NEC Pages: 28

Brand: IBM Pages: 462

Brand: Igel Pages: 2

Brand: iDOT Pages: 66

PC 300GL Type 6267

Brand: IBM Pages: 58

Brand: Steinberg Pages: 820

Brand: Amplicon Pages: 92

DECstaion 5000 240

Brand: Digital Equipment Pages: 62

Brand: Contec Pages: 116

Brand: IBM Pages: 2

Brand: Vivo Pages: 3

Brand: BTOD Pages: 12

9120A4U - ThinkCentre A61 - 9120

Brand: Lenovo Pages: 66

Brand: Lenovo Pages: 76

Brand: Lenovo Pages: 64

Brand: Lenovo Pages: 98

Brand: Lenovo Pages: 86

Brand: Lenovo Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands