Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 112

Page: 112 / 170

2. Connect the front antenna cable and rear antenna cable to the WiFi card module.

Figure 42. Installing the WiFi antenna cables

3. Install the WiFi adapter card into the PCI Express x1 slot on the system board. See “Locating parts on

the system board” on page 72.

4. If the installed WiFi card module supports the Bluetooth function, use a Bluetooth cable to connect the

Bluetooth connector on the WiFi adapter card to the front USB connector on the system board.

5. Pivot the card latch to the closed position to secure the WiFi adapter card.

Figure 43. Installing the WiFi adapter card

What to do next:

• To work with another piece of hardware, go to the appropriate section.

108

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands