Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 78

Page: 78 / 170

Locating connectors, controls, and indicators on the front of your
computer

Figure 6 “Front connector, control, and indicator locations” on page 74 shows the locations of the
connectors, controls, and indicators on the front of your computer.

Figure 6. Front connector, control, and indicator locations

Optical drive eject/close button

USB connector (USB port 2)

Power switch

Microphone connector

Hard disk drive activity indicator

Headphone connector

Power indicator

USB connector (USB port 1)

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands