Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 129

Page: 129 / 170

6. Disconnect the signal cable and the power cable from the hard disk drive to completely remove the hard

disk drive from the chassis.

7. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an

available SATA connector on the system board. See “Locating parts on the system board” on page 79.
Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive.

Figure 63. Connecting a SATA hard disk drive

8. Position the new hard disk drive into the hard disk drive bay and align the screw holes in the new hard

disk drive with the corresponding holes in the drive bay. Then, install the four screws to secure the
new hard disk drive in place.

Figure 64. Installing the hard disk drive

9. To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Replacing the optical drive

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

Chapter 10

Replacing FRUs (Machine Types: 3493, 3496, and 3497)

125

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands