Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 113

Page: 113 / 170

• To complete the installation or replacement, go to “Completing the parts replacement” on page 112.

Installing or removing the rear WiFi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
on page 1.

This section provides instructions on how to install or remove the rear WiFi antenna.

Installing the rear WiFi antenna

To install the rear WiFi antenna, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Install the rear WiFi antenna to the rear WiFi antenna cable connector attached on the rear of the

computer.

3. Adjust the angle of the rear antenna to lower the risk of breaking the antenna by accident.

Figure 44. Installing the rear WiFi antenna

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 112.

Removing the rear WiFi antenna

To remove the rear WiFi antenna, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Straighten the rear WiFi antenna so that it can be more easily twisted.

Chapter 9

Replacing FRUs (Machine Types: 3484, 3485, and 3492)

109

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands