Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download

Page: 109 / 170

5. Grasp the WiFi adapter card that is currently installed and gently pull it out of the slot.

Figure 37. Removing the WiFi adapter card

Note:

The card fits tightly into the card slot. If necessary, alternate moving each side of the card a

small amount until it is removed from the card slot.

Removing the WiFi card module

To remove the WiFi card module, do the following:

1. Remove the WiFi adapter card from the computer, and then disconnect the front and rear WiFi antenna

cables from the WiFi card module.

Figure 38. Removing the WiFi antenna cables

Chapter 9

Replacing FRUs (Machine Types: 3484, 3485, and 3492)

105

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands