Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 71

Page: 71 / 170

Chapter 8. Locations

This chapter introduces the locations of the computer hardware components.

Locations

This section provides information to help you locate your computer connectors, components, parts on
the system board, and internal drives.

Note:

The components in your computer might look slightly different from the illustrations.

Locating connectors, controls, and indicators on the front of your
computer

Figure 1 “Front connector, control, and indicator locations” on page 67 shows the locations of the
connectors, controls, and indicators on the front of your computer.

Figure 1. Front connector, control, and indicator locations

Hard disk drive activity indicator

USB connector (USB port 1)

Power indicator

Headphone connector

Power switch

Microphone connector

Optical drive eject/close button

USB connector (USB port 2)

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands