Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 148

Page: 148 / 170

4. Pivot the drive bay assembly upward. See “Accessing the system board components and drives” on

page 118.

5. Disconnect the front audio and USB assembly cables from the system board. See “Locating parts on

the system board” on page 79.

Note:

Make sure you note the locations of the cables when you disconnect the cables from the system

board.

6. Remove the screw that secures the front audio and USB assembly bracket to the chassis to remove

the bracket from the chassis.

Figure 85. Removing the front audio and USB assembly

7. Install the front audio and USB assembly bracket into the chassis and align the screw hole in the

bracket with the corresponding hole in the chassis.

8. Install the screw to secure the bracket to the chassis.

9. Pivot the drive bay assembly upward and reconnect the front USB and front audio cables to the system

board. See “Locating parts on the system board” on page 79.

10. Reconnect the front audio and USB assembly cables to the front audio connector and the front USB

connector on the system board. See “Locating parts on the system board” on page 79.

11. Lower the drive bay assembly. See “Accessing the system board components and drives” on page 118.

12. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 117.

13. To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Replacing the WiFi units

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
on page 1.

This section provides instructions on how to replace the WiFi units. The WiFi units include a WiFi adapter
card, a WiFi card module, and a rear WiFi antenna cable.

Replacing the WiFi units involves the following operations:

144

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands