Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 44

Page: 44 / 170

DVD problems

Select your symptom from the following list:

•

“Black screen instead of DVD video” on page 40

•

“DVD movie will not play” on page 40

•

“No audio or intermittent audio while playing DVD movie” on page 40

•

“Playback is very slow or choppy” on page 40

•

“Invalid disc or no disc found message” on page 41

Black screen instead of DVD video

Symptom: Black screen instead of DVD video

Actions:

• Restart the DVD player program.

• Close any open files, turn off the computer, and then restart the computer.

• Try a lower screen resolution or color depth.

If these actions do not correct the problem, run the diagnostic programs (see “Lenovo Solution Center” on
page 53 for instructions). If you need technical assistance, see “Lenovo Support Web site” on page 32.

DVD movie will not play

Symptom: DVD movie will not play.

Actions:

• Make sure that the disc surface is clean and not scratched.

• Check the disc or package for regional coding. You might need to purchase a disc with coding for

the region where you are using your computer.

No audio or intermittent audio while playing DVD movie

Symptom: No audio or intermittent audio while playing DVD movie.

Actions:

• Check the volume control settings on your computer and on your speakers.

• Make sure that the disc surface is clean and not scratched.

• Check all cable connections to and from the speakers.

• Use the DVD menu for the video to select a different audio track.

Playback is very slow or choppy

Symptom: Playback is very slow or choppy.

Actions:

• Disable any background programs, such as AntiVirus or Desktop Themes.

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands