Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 139

Page: 139 / 170

6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the

system board:

a. Partially remove screw

, then fully remove screw

, and then fully remove screw

b. Partially remove screw

, then fully remove screw

, and then fully remove screw

Note:

Carefully remove the four screws from the system board to avoid any possible damage to the

system board. The four screws cannot be removed from the heat sink and fan assembly.

Figure 76. Removing the heat sink and fan assembly

7. Lift the failing heat sink and fan assembly off the system board.

Notes:

a. You might have to gently twist the heat sink and fan assembly to free it from the microprocessor.

b. When handling the heat sink and fan assembly, do not touch the thermal grease on the bottom

of the heat sink and fan assembly.

8. Place the new heat sink and fan assembly on the system board so that the four screws are aligned with

the corresponding holes in the system board.

Note:

Position the new heat sink and fan assembly so that the heat sink and fan assembly cable is

toward the microprocessor fan connector on the system board.

9. Follow the following sequence to install the four screws to secure the new heat sink and fan assembly.

Do not over-tighten the screws.

a. Partially tighten screw

, then fully tighten screw

, and then fully tighten screw

b. Partially tighten screw

, then fully tighten screw

, and then fully tighten screw

10. Connect the new heat sink and fan assembly cable to the microprocessor fan connector on the system

board. See “Locating parts on the system board” on page 79.

11. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until it snaps

into position.

Chapter 10

Replacing FRUs (Machine Types: 3493, 3496, and 3497)

135

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands