Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download

Page: 4 / 170

Locating connectors on the rear of your
computer . . . . . . . . . . . . . . .

Locating major FRUs and CRUs . . . . . .

Looking up FRU information . . . . . . .

Locating parts on the system board

. . . .

Locating internal drives . . . . . . . . .

Chapter 9. Replacing FRUs (Machine
Types: 3484, 3485, and 3492) . . . . .

Handling static-sensitive devices . . . . . . .

Installing or replacing hardware . . . . . . . .

Removing the computer cover. . . . . . .

Removing and reinstalling the front bezel . .

Installing or replacing a PCI card . . . . . .

Replacing the battery . . . . . . . . . .

Installing or replacing a memory module . . .

Replacing the optical drive . . . . . . . .

Replacing the heat sink and fan assembly . .

Replacing the power supply assembly

. . .

Replacing the microprocessor . . . . . . .

Replacing the system board

. . . . . . .

Replacing the primary hard disk drive . . . .

100

Replacing the front audio and USB
assembly . . . . . . . . . . . . . . .

102

Replacing the WiFi units . . . . . . . . .

103

Installing or removing the rear WiFi antenna . .

109

Installing or removing the front WiFi
antenna

. . . . . . . . . . . . . . .

110

Completing the parts replacement . . . . .

112

Chapter 10. Replacing FRUs (Machine
Types: 3493, 3496, and 3497) . . . .

115

Handling static-sensitive devices . . . . . . .

115

Installing or replacing hardware . . . . . . . .

115

Removing the computer cover. . . . . . .

116

Removing and reinstalling the front bezel . .

117

Accessing the system board components and
drives . . . . . . . . . . . . . . . .

118

Installing or replacing a PCI card . . . . . .

119

Installing or replacing a memory module . . .

121

Replacing the battery . . . . . . . . . .

122

Replacing the hard disk drive . . . . . . .

123

Replacing the optical drive . . . . . . . .

125

Replacing the power supply assembly

. . .

129

Replacing the heat sink and fan assembly . .

133

Replacing the microprocessor . . . . . . .

136

Replacing the system board

. . . . . . .

139

Replacing the system fan assembly

. . . .

141

Replacing the front audio and USB
assembly . . . . . . . . . . . . . . .

143

Replacing the WiFi units . . . . . . . . .

144

Installing or removing the rear WiFi antenna . .

149

Installing or removing the front WiFi
antenna

. . . . . . . . . . . . . . .

151

Replacing the keyboard or mouse . . . . .

153

Completing the parts replacement . . . . .

154

Chapter 11. Additional service
information . . . . . . . . . . . . .

157

Security features . . . . . . . . . . . . . .

157

Hardware-controlled passwords . . . . . .

157

Operating system password

. . . . . . .

157

Vital Product Data

. . . . . . . . . . .

157

BIOS levels . . . . . . . . . . . . . . . .

157

Flash update procedures

. . . . . . . . . .

157

Updating (flashing) the BIOS from a disc. . .

158

Updating (flashing) the BIOS from your
operating system . . . . . . . . . . . .

159

Recovering from a POST and BIOS update
failure . . . . . . . . . . . . . . . .

159

Power management

. . . . . . . . . . . .

160

Advanced Configuration and Power Interface
(ACPI) BIOS . . . . . . . . . . . . . .

160

Automatic Power-on features . . . . . . .

160

Appendix A. Notices . . . . . . . . .

161

Television output notice . . . . . . . . . . .

162

European conformance CE mark . . . . . . .

162

Trademarks . . . . . . . . . . . . . . . .

162

Index. . . . . . . . . . . . . . . . .

163

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands