Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download

Page: 149 / 170

•

“Removing the WiFi adapter card” on page 145

•

“Removing the WiFi card module” on page 146

•

“Installing the WiFi units” on page 147

Removing the WiFi adapter card

To remove the WiFi adapter card, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. If your computer comes with a WiFi card module that supports the Bluetooth function, disconnect

the Bluetooth cable from the WiFi adapter card.

Figure 86. Disconnecting the Bluetooth cable

Note:

The Bluetooth cable connects the Bluetooth connector on the WiFi adapter card to the front USB

connector on the system board to support the Bluetooth function.

4. Remove the screw that secures the WiFi adapter card.

Chapter 10

Replacing FRUs (Machine Types: 3493, 3496, and 3497)

145

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands