Lenovo ThinkCentre Edge 3484 Hardware Maintenance Manual Download Page 144

Page: 144 / 170

8. Remove the six screws that secure the system board.

Figure 81. Removing the six screws that secure the system board

9. Lift the system board out of the chassis.

10. Remove the microprocessor from the failing system board and install it on the new system board. See

“Replacing the microprocessor” on page 136.

11. Install the new system board into the chassis by aligning the six mounting studs in the chassis with the

corresponding holes in the new system board. Then, install the six screws to secure the system board.

12. Install the heat sink and fan assembly and connect the heat sink and fan assembly cable to the new

system board. See “Replacing the heat sink and fan assembly” on page 133.

13. Install all memory modules and PCI cards removed from the failing system board on the new system

board. See “Installing or replacing a memory module” on page 121 and “Installing or replacing a PCI
card” on page 119.

14. Reconnect all remaining cables to the system board. See “Locating parts on the system board”

on page 79.

15. Lower the optical drive bay assembly.

16. To complete the replacement, go to “Completing the parts replacement” on page 154.

The failing system board must be returned with a microprocessor socket cover to protect the pins during
shipping and handling.

To install the microprocessor socket cover, do the following:

1. Release the lever securing the microprocessor retainer and open the retainer to access the

microprocessor.

140

ThinkCentre Hardware Maintenance Manual

Summary of Contents for ThinkCentre Edge 3484











































































































































































Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands

Lenovo ThinkCentre Edge 3484, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre Edge 3484

Reviews:

Related manuals for ThinkCentre Edge 3484

Brands by name

Popular brands