Lenovo HX1310 Installation And Service Manual Download Page 136

Page: 136 / 1002

Table 28. Configuration 1 (HX1310 only)

Configuration 1

PCI riser-card assembly

connector 1 on system board

PCI riser-card assembly

connector 2 on system board

Configuration

Number of

microprocessors

installed

Slot 1

Slot 2

Slot 3

• Three

low-profile slots

One

x1/x4/x8/x16 low-profile

x1/x4/x8

low-profile

x1/x4/x8

low-profile

Table 29. Configuration 2 (HX2310-E, HX3310, HX3310-F)

Configuration 2

PCI riser-card assembly

connector 1 on system board

PCI riser-card assembly

connector 2 on system board

Configuration

Number of

microprocessors

installed

Slot 1

Slot 2

Slot 3

• Three

low-profile

slots

Two

x1/x4/x8/x16 low-profile

x1/x4/x8/x16

low-profile

x1/x4/x8/x16

low-profile

To install a PCI riser-card assembly, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 104).

Step 4.

Install the adapter in the new PCI riser-card assembly (see “Replacing an adapter” on page 126).

Step 5.

Set any jumpers or switches on the adapter as directed by the adapter manufacturer.

Step 6.

Remove the PCI filler panel, if one is present, from the rear of the server.

122

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands