Lenovo HX1310 Installation And Service Manual Download Page 964

Page: 964 / 1002

•

202-802-000 : MemStr Test Aborted

Memory size is insufficient to run the test. At least 1 GB is required.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-803-000 : MemStr Test Aborted

User pressed Ctrl-C.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-901-000 : MemStr Test Failed

Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

950

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands