Lenovo HX1310 Installation And Service Manual Download Page 718

Page: 718 / 1002

•

816f0308-0a02ffff : [PowerSupplyElementName] has returned to a Normal Input State. (Power

Supply 2)

This message is for the use case when an implementation has detected a Power Supply that has input
that has returned to normal.

May also be shown as 816f03080a02ffff or 0x816f03080a02ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0099

User Response

No action; information only.

•

816f030c-2001ffff : Scrub Failure for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName] has recovered. (DIMM 1)

This message is for the use case when an implementation has detected a Memory Scrub failure recovery.

May also be shown as 816f030c2001ffff or 0x816f030c2001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0137

User Response

No action; information only.

704

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands