manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 160

Front USB assembly

Figure 68. Front USB connector assembly installation for eight 2.5-inch hot-swap hard disk drive server
configuration

Step 3.

Carefully push the media cage back into the chassis (see “Replacing the media cage” on page
143). Remember to reconnect the cables that were removed from the system board.

Step 4.

Reinstall the cover (see “Replacing the cover” on page 105).

Step 5.

Reconnect the power cords and any cables that you removed.

Step 6.

Slide the server into the rack.

Step 7.

Turn on the peripheral devices and the server.

Removing the front video connector assembly

Use this information to remove the front video connector assembly.

To remove the front video connector assembly, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the cover (see “Removing the cover” on page 104).

Step 4.

Remove the media cage (see “Removing the media cage” on page 142).

Step 5.

Loosen the screws that secure the front video connector assembly to the media cage; then, remove
the assembly from the media cage.

146

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands