Lenovo HX1310 Installation And Service Manual Download Page 60

Page: 60 / 1002

This option allows the OS (hypervisor) to control the node power. Many customers prefer this setting as it
saves on OPEX.

Use the Lenovo ToolsCenter Suite CLI program or other means to set the power performance bias to
“OS Controlled”:

onecli config set Power.PowerPerformanceBias “OS Controlled”

Modify boot options

Use the Lenovo ToolsCenter Suite CLI program or other means to configure the boot order as follows:

1. CD/DVD Rom

2. Hard Disk 0

3. PXE Network

onecli config set BootOrder.BootOrder=”Legacy Only=CD/DVD Rom=Hard Disk 0=PXE Network”

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands