manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 479

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0170

User Response

No action; information only.

•

806f030d-040dffff : Hot Spare enabled for [ComputerSystemElementName]. (Drive 13)

This message is for the use case when an implementation has detected a Hot Spare has been Enabled.

May also be shown as 806f030d040dffff or 0x806f030d040dffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0170

User Response

No action; information only.

•

806f030d-0410ffff : Hot Spare enabled for [ComputerSystemElementName]. (Ext Drive)

This message is for the use case when an implementation has detected a Hot Spare has been Enabled.

May also be shown as 806f030d0410ffff or 0x806f030d0410ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

465

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands