Lenovo HX1310 Installation And Service Manual Download Page 878

Page: 878 / 1002

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-004-000 : IANet:Loopback Test Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-800-000 : IANet:Registers Test Aborted

Registers test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-801-000 : IANet:EEPROM Test Aborted

EEPROM test was canceled.

Recoverable

864

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands