Lenovo HX1310 Installation And Service Manual Download Page 680

Page: 680 / 1002

•

816f0021-3001ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (Internal RAID)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00213001ffff or 0x816f00213001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only. PCI 1 :

•

816f0021-3002ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (PCI 2)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00213002ffff or 0x816f00213002ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only.

666

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands