Lenovo HX1310 Installation And Service Manual Download Page 121

Page: 121 / 1002

Step 4.

Grasp the air baffle, disengage pins from pin holes; then, lift the air baffle up and set it aside.

Baffle pin hole

Baffle pin

Baffle pin hole

Air baffle

Figure 32. Air baffle removal

Attention:

For proper cooling and airflow, replace the air baffle before you turn on the server.

Operating the server with the air baffle removed might damage server components.

Replacing the air baffle

Use this information to replace the air baffle.

To install the air baffle, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Step 3.

Remove the cover (see “Removing the cover” on page 104).

Chapter 5

Removing and replacing components

107

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands