manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 687

•

816f010c-2007ffff : Uncorrectable error recovery detected for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 7)

This message is for the use case when an implementation has detected a Memory uncorrectable error
recovery.

May also be shown as 816f010c2007ffff or 0x816f010c2007ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

Critical - Memory

SNMP Trap ID

41

CIM Information

Prefix:

PLAT

ID:

0139

User Response

No action; information only.

•

816f010c-2008ffff : Uncorrectable error recovery detected for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 8)

This message is for the use case when an implementation has detected a Memory uncorrectable error
recovery.

May also be shown as 816f010c2008ffff or 0x816f010c2008ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

Critical - Memory

SNMP Trap ID

41

CIM Information

Prefix:

PLAT

ID:

0139

User Response

No action; information only.

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

673

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands