manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 706

This message is for the use case when an implementation has detected an Interconnect Configuration
was Repaired.

May also be shown as 816f011b0c01ffff or 0x816f011b0c01ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

Critical - Other

SNMP Trap ID

50

CIM Information

Prefix:

PLAT

ID:

0267

User Response

No action; information only.

•

816f0125-0c01ffff : [ManagedElementName] detected as present. (Front Panel)

This message is for the use case when an implementation has detected a Managed Element is now
Present.

May also be shown as 816f01250c01ffff or 0x816f01250c01ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0390

User Response

No action; information only.

•

816f0125-1001ffff : [ManagedElementName] detected as present. (PCI Riser 1)

692

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands