manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

The Lenovo HX1310 Installation and Service Manual is available for free download on our website. This comprehensive manual provides step-by-step instructions and guidelines for setting up and maintaining the Lenovo HX1310. Visit our website today to access this essential manual for your Lenovo HX1310.

Share
Download
background image

Removing and replacing consumable and structural parts

Replacement of consumable and structural parts is your responsibility. If Lenovo installs a consumable and
structural part at your request, you will be charged for the installation.

The illustrations in this document might differ slightly from your hardware.

Removing the cover

Use this information to remove the cover.

To remove the server cover, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Note:

If you need to view any LEDs on the system board or front panel, ensure that you view

the LEDs before disconnect the power cords.

Step 3.

If the server has been installed in a rack, slide the server out from the rack enclosure.

Step 4.

Remember to check if the cover is locked. If it is locked, unlock the cover first.

Latch

00

00

Lock

Unlock

Figure 28. Unlocking the cover

104

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX1310

NEC NEAX2000 IVS Series System Manual preview
NEAX2000 IVS Series
Brand: NEC Pages: 160
7starlake ROC286B User Manual preview
ROC286B
Brand: 7starlake Pages: 32
Hologic Cenova User Manual preview
Cenova
Brand: Hologic Pages: 30
BELINEA o.center User Manual preview
o.center
Brand: BELINEA Pages: 53
Panasonic AG-JJLBE20P Operating Instructions Manual preview
AG-JJLBE20P
Brand: Panasonic Pages: 17
Panasonic AJ-HDR150P Operating Instructions Manual preview
AJ-HDR150P
Brand: Panasonic Pages: 42
Panasonic KX-NSX1000 Operating Manual preview
KX-NSX1000
Brand: Panasonic Pages: 316
Panasonic KX-NSX1000 Manual preview
KX-NSX1000
Brand: Panasonic Pages: 456
ICP DAS USA UA-5000 series User Manual preview
UA-5000 series
Brand: ICP DAS USA Pages: 59
Gigabyte R272-P32 User Manual preview
R272-P32
Brand: Gigabyte Pages: 86
Gigabyte G492-HA0 User Manual preview
G492-HA0
Brand: Gigabyte Pages: 110
Gigabyte R283-Z93-AAF1 User Manual preview
R283-Z93-AAF1
Brand: Gigabyte Pages: 173
Gigabyte H273-Z81-AAN1 User Manual preview
H273-Z81-AAN1
Brand: Gigabyte Pages: 166
Gigabyte G492-ZD2 User Manual preview
G492-ZD2
Brand: Gigabyte Pages: 134
Obvius AcquiLite A7810 Installation And Operation Manual preview
AcquiLite A7810
Brand: Obvius Pages: 29
QNAP NAS TS-877XU-RP-3600-8G-US Quick Installation Manual preview
NAS TS-877XU-RP-3600-8G-US
Brand: QNAP Pages: 12
QNAP Nextephive User Manual preview
Nextephive
Brand: QNAP Pages: 15
ICPDAS PDS-811 User Manual preview
PDS-811
Brand: ICPDAS Pages: 104

Brands by name

Popular brands

Load more brands