manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 275

UEFI Definitions change has been detected

May also be shown as 4000009800000000 or 0x4000009800000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0152

User Response

Information only; no action is required.

•

40000099-00000000 : Security: Userid: [arg1] had [arg2] login failures from IPMI client at IP

address [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from IPMI.

May also be shown as 4000009900000000 or 0x4000009900000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Remote Login

SNMP Trap ID

30

CIM Information

Prefix:

IMM

ID:

0153

User Response

Information only; no action is required.

•

4000009a-00000000 : Security: Userid: [arg1] had [arg2] login failures from SNMP client at IP

address [arg3].

This message is for the use case where a user has failed to access a Management Controller from SNMP.

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

261

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands