Lenovo HX1310 Installation And Service Manual Download Page 860

Page: 860 / 1002

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

405-800-000 : BRCM:TestControlRegisters Test Aborted

The control registers test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

405-801-000 : BRCM:TestMIIRegisters Test Aborted

The MII register test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

846

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands