Lenovo HX1310 Installation And Service Manual Download Page 927

Page: 927 / 1002

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-861-002 : Standalone Memory Test Aborted

No SRAT type 1 found.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-861-003 : Standalone Memory Test Aborted

No SRAT type 1 found.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

Appendix C. DSA diagnostic test results

913

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands