Lenovo HX1310 Installation And Service Manual Download Page 977

Page: 977 / 1002

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-823-001 : IMM I2C Test Aborted

Cannot execute command. Insufficient privilege level.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-824-001 : IMM I2C Test Aborted

Cannot execute command.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

Appendix C. DSA diagnostic test results

963

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Brands by name

Popular brands