Lenovo HX1310 Installation And Service Manual Download Page 789

Page: 789 / 1002

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-200effff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 14)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c200effff or 0x816f070c200effff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-200fffff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 15)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c200fffff or 0x816f070c200fffff

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

775

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands