Lenovo HX1310 Installation And Service Manual Download Page 614

Page: 614 / 1002

•

81010204-1d05ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 5A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d05ffff or 0x810102041d05ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 5B Tach :

•

81010204-1d06ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 6A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d06ffff or 0x810102041d06ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 6B Tach :

600

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands