Lenovo HX1310 Installation And Service Manual Download Page 303

Page: 303 / 1002

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0212

User Response

Check storage documentation by LSI Event ID.

•

400000d5-00000000 : One or more virtual drives have problem. Please contact technical support to

resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])

One or more virtual drives have problem

May also be shown as 400000d500000000 or 0x400000d500000000

Severity

Info

Serviceable

Automatically notify support

Yes

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0213

User Response

Check storage documentation by LSI Event ID.

•

400000d6-00000000 : Drive error was detected by RAID controller. Please contact technical

support to resolve this issue.([arg1],[arg2],[arg3],[arg4],[arg5])

Drive error was detected by RAID controller

May also be shown as 400000d600000000 or 0x400000d600000000

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

289

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands