Lenovo HX1310 Installation And Service Manual Download Page 877

Page: 877 / 1002

•

406-001-000 : IANet:EEPROM Test Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-002-000 : IANet:FIFO Test Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-003-000 : IANet:Interrupts Test Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Appendix C. DSA diagnostic test results

863

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands