manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

The Lenovo HX1310 Installation and Service Manual is available for free download on our website. This comprehensive manual provides step-by-step instructions and guidelines for setting up and maintaining the Lenovo HX1310. Visit our website today to access this essential manual for your Lenovo HX1310.

Share
Download
background image

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0392

User Response

If there is no GPU/storage tray installed in the system, then the log event is a normal condition. If
there is a GPU/storage tray installed in the system, then check the following two portions:

1. PDB (Power Distribution Board) cable is correctly connected from riser card to PDB.

2. Replace another PDB cable.

•

806f0207-0301ffff : [ProcessorElementName] has Failed with FRB1/BIST condition. (CPU 1)

This message is for the use case when an implementation has detected a Processor Failed - FRB1/BIST
condition.

May also be shown as 806f02070301ffff or 0x806f02070301ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - CPU

SNMP Trap ID

40

CIM Information

Prefix:

PLAT

ID:

0044

User Response

1. Make sure that the latest levels of firmware and device drivers are installed for all adapters and

standard devices, such as Ethernet, SCSI, and SAS. Important: Some cluster solutions require
specific code levels or coordinated code updates. If the device is part of a cluster solution, verify
that the latest level of code is supported for the cluster solution before you update the code.

2. Update the firmware (UEFI and IMM) to the latest level (Updating the firmware).

3.

Run the DSA program.

4.

Reseat the adapter.

5.

Replace the adapter.

424

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX1310

IBM i Series Handbook preview
i Series
Brand: IBM Pages: 908
IBM 990 Reference Manual preview
990
Brand: IBM Pages: 88
Xerox Phaser EX7750 Configuration Manual preview
Phaser EX7750
Brand: Xerox Pages: 220
Xerox Phaser EX7750 Quick Start Manual preview
Phaser EX7750
Brand: Xerox Pages: 28
Xerox DocuPrint 100MX Install Manual preview
DocuPrint 100MX
Brand: Xerox Pages: 2
Premio FlacheSAN1L-D4 Quick Manual preview
FlacheSAN1L-D4
Brand: Premio Pages: 3
IBM totalstorage 200 Hardware Installation Manual preview
totalstorage 200
Brand: IBM Pages: 152
Blackberry Enterprise Server Upgrade Manual preview
Enterprise Server
Brand: Blackberry Pages: 88
Supermicro SSG-927R-E2CJB User Manual preview
SSG-927R-E2CJB
Brand: Supermicro Pages: 62
Premio FlacheSAN2-D5 Quick Manual preview
FlacheSAN2-D5
Brand: Premio Pages: 2
Intergraph InterServe 600 Series System Reference Manual preview
InterServe 600 Series
Brand: Intergraph Pages: 104
Simpact Freeway 1200 Hardware Installation Manual preview
Freeway 1200
Brand: Simpact Pages: 76
Avaya callpilot 1002rp Maintenance And Diagnostics preview
callpilot 1002rp
Brand: Avaya Pages: 150
Black Box PCA35A-R3 User Manual preview
PCA35A-R3
Brand: Black Box Pages: 30
DataOn Storage CiB-9224 V12 Technical Manual preview
CiB-9224 V12
Brand: DataOn Storage Pages: 36
Philips System4 Seriver Installation Instructions Manual preview
System4 Seriver
Brand: Philips Pages: 48
National Instruments ENET-Serial Getting Started preview
ENET-Serial
Brand: National Instruments Pages: 4
ZyXEL Communications NPS-520 Quick Start Manual preview
NPS-520
Brand: ZyXEL Communications Pages: 115

Brands by name

Popular brands

Load more brands