Lenovo HX1310 Installation And Service Manual Download Page 740

Page: 740 / 1002

User Response

No action; information only.

•

816f040c-2004ffff : [PhysicalMemoryElementName] Enabled on Subsystem

[MemoryElementName]. (DIMM 4)

This message is for the use case when an implementation has detected that Memory has been Enabled.

May also be shown as 816f040c2004ffff or 0x816f040c2004ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0130

User Response

No action; information only.

•

816f040c-2005ffff : [PhysicalMemoryElementName] Enabled on Subsystem

[MemoryElementName]. (DIMM 5)

This message is for the use case when an implementation has detected that Memory has been Enabled.

May also be shown as 816f040c2005ffff or 0x816f040c2005ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0130

User Response

726

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands

Lenovo HX1310, Installation And Service Manual

Search results

Summary of Contents for HX1310

Reviews:

Related manuals for HX1310

Brands by name

Popular brands