manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

22

E

C

C

12

13

14

14

C

13

12

E

C

Einstellen des DP-Öffnungs-/

Schließungswinkels

Einstellung des DP-Öffnungs-/

Schließungswinkels auf 60 Grad

1.

Den Winkeleinstellhalter (C) einsetzen und 
mit einer M4 × 14 Schraube (E) befestigen.

Einstellung des DP-Öffnungs-/

Schließungswinkels auf 30 Grad

1.

Die zwei Sicherungsringe (12) entfernen, 
und die Achse (13) herausziehen.

2.

Die Achse (13) in die Löcher (14) einführen, 
und die zwei Sicherungsringe (12) wieder 
anbringen.

3.

Den Winkeleinstellhalter (C) einsetzen und 
mit einer M4 × 14 Schraube (E) befestigen.

Ajuste del ángulo de apertura/cierre del 

DP

Para ajustar el ángulo de apertura/cierre del 

DP a 60 grados

1.

Inserte la placa de ajuste de ángulo (C) y fije 
con el tornillo M4 × 14 (E).

Para ajustar el ángulo de apertura/cierre del 

DP a 30 grados

1.

Desmonte los dos aros de tope (12) y tire del 
eje (13) hacia fuera.

2.

Inserte el eje (13) en los orificios (14) y 
vuelva a colocar los dos aros de tope (12).

3.

Inserte la placa de ajuste de ángulo (C) y fije 
con el tornillo M4 × 14 (E).

Réglage de l’angle d’ouverture/

fermeture du DP

Pour régler l’angle d’ouverture/fermeture du 

DP à 60 degrés

1.

Insérez la plaque de réglage d’angle (C), et 
fixez-la à l’aide d’une vis M4 × 14 (E).

Pour régler l’angle d’ouverture/fermeture du 

DP à 30 degrés

1.

Retirez deux bagues d’arrêt (12) et tirez 
l’arbre (13) vers l’extérieur.

2.

Insérez l’arbre (13) dans les orifices (14) et 
remettez les deux bagues d’arrêt (12) en 
place.

3.

Insérez la plaque de réglage d’angle (C), et 
fixez-la à l’aide d’une vis M4 × 14 (E).

Regolazione dell’angolo di apertura e 

chiusura del DP

Per regolare l’angolo di apertura e chiusura 

del DP a 60 gradi

1.

Inserire la piastra di regolazione dell’angolo 
(C) e fissarla con una vite M4 × 14 (E).

Per regolare l’angolo di apertura e chiusura 

del DP a 30 gradi

1.

Rimuovere i due anelli di arresto (12) ed 
estrarre l’albero (13).

2.

Inserire l’albero (13) nei fori (14) e fissare 
nuovamente i due anelli di arresto (12).

3.

Inserire la piastra di regolazione dell’angolo 
(C) e fissarla con una vite M4 × 14 (E).

调整 DP 的角度

设定 60 度的 DP 开闭角度时

1. 插入调整板 (C)，用 1 个螺丝

M4 × 14(E) 进行固定。

设定 30 度的 DP 角度时

1. 拆下 2 个止动环 (12)，拔下轴 (13)。
2. 将轴 (13) 插入孔 (14)，并将 2 个止动环 (12)

按原样装好。

3. 插入调整板 (C)，用 1 个螺丝

M4 × 14(E) 进行固定。

DP 開閉角度の調整

DP 開閉角度を 60°に設定する場合

1.

調整板 (C) を挿入し、

ビス M4 × 14(E)1 本で

固定する。

DP 開閉角度を 30°に設定する場合

1.

ストップリング (12)2 個を外し、軸 (13) を
引き抜く。

2.

軸 (13) を穴 (14) に挿入し、ストップリング
(12)2 個を元通り取り付ける。

3.

調整板 (C) を挿入し、

ビス M4 × 14(E)1 本で

固定する。

Adjusting the DP open/close angle

To adjust the DP open/close angle to 60 

degrees

1.

Insert the angle adjusting plate (C) and fit it 
using M4 × 14 screw (E).

To adjust the DP open/close angle to 30 

degrees

1.

Remove two stop rings (12) and pull the 
shaft (13) out.

2.

Insert the shaft (13) into the holes (14) and 
refit two stop rings (12).

3.

Insert the angle adjusting plate (C) and fit it 
using M4 × 14 screw (E).

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Canon Pixma MG2400 Series Getting Started Manual preview
Pixma MG2400 Series
Brand: Canon Pages: 2
Canon imagePROGRAF W8400 Driver Manual preview
imagePROGRAF W8400
Brand: Canon Pages: 24
Canon imagePROGRAF TZ-30000 Setup Manual preview
imagePROGRAF TZ-30000
Brand: Canon Pages: 66
Canon imagePROGRAF W7200 Setup Manual preview
imagePROGRAF W7200
Brand: Canon Pages: 126
Canon imagePROGRAFi iPF840 series Basic Manual preview
imagePROGRAFi iPF840 series
Brand: Canon Pages: 149
Canon IPF850 Basic Manual preview
IPF850
Brand: Canon Pages: 166
Canon iP4000 - PIXMA Photo Printer Start Here preview
iP4000 - PIXMA Photo Printer
Brand: Canon Pages: 2
Olympus P 400 Firmware Upgrade Manual preview
P 400
Brand: Olympus Pages: 3
Canon BW Remote Operators Software Kit-A1 Service Manual preview
BW Remote Operators Software Kit-A1
Brand: Canon Pages: 20
Canon imageRUNNER 2420 Trouble Error Codes List preview
imageRUNNER 2420
Brand: Canon Pages: 30
Canon IPF850 Service Manual preview
IPF850
Brand: Canon Pages: 51
Canon imageCLASS LBP325dn Service Manual preview
imageCLASS LBP325dn
Brand: Canon Pages: 252
SPRT SP-T6 User Manual preview
SP-T6
Brand: SPRT Pages: 28
Oki B411d Guía Del Usuario preview
B411d
Brand: Oki Pages: 154
Oki ML320 Turbo Manual Do Utilizador preview
ML320 Turbo
Brand: Oki Pages: 121
Oki B4100 Guía Del Usuario preview
B4100
Brand: Oki Pages: 96
Pandigital ZINK PANPRINT01 Quick Start Manual preview
ZINK PANPRINT01
Brand: Pandigital Pages: 2
Xerox WorkCentre 7800 series Quick Reference Manual preview
WorkCentre 7800 series
Brand: Xerox Pages: 14

Brands by name

Popular brands

Load more brands