manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-5-27

8. Loop the outer ends of the scanner wires around the outer grooves in the pulleys on the mirror 2 frame, 

winding from below to above. .......................................................................................................................... (1)

9. Hook the round terminals onto the catches inside the scanner unit. ............................................................... (2)
10. Loop the inner ends of the scanner wires around the grooves in the pulleys at the left of the scanner unit, 

winding from below to above. .......................................................................................................................... (3)

11. Loop the scanner wires around the inner grooves in the pulleys on the mirror 2 frame, winding from 

above to below................................................................................................................................................. (4)

12. Wind the scanner wires around the grooves in the scanner wire guides at the left of the scanner unit. ......... (5)
13. Hook the round terminals onto the scanner wire springs................................................................................. (6)

Figure 1-5-49

14. Remove the two scanner wire stoppers and 

frame securing tools.

15. Focusing on the locating ball of the wire 

drum, move aside the wires to inside.

16. Move the mirror 2 frame from side to side to 

correctly locate the wires in position.

17. Refit the mirror 1 frame.
18. Move the mirror 1 and 2 frames to the 

machine left, and insert the two frame secur-
ing tools into the positioning holes at the 
front and rear of the scanner unit to secure 
the frames in position.

19. Hold the wires and fix each front and rear 

wire holder plate to mirror 1 frame with the 
screw.

20. Remove the two frame securing tools.
21. Refit all the removed parts.

Figure 1-5-50

Frame securing tool

Frame securing tool

Mirror 2 frame

Mirror 1 frame

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

NEC 870 - SuperScript B/W Laser Printer Network Quickstart preview
870 - SuperScript B/W Laser Printer
Brand: NEC Pages: 8
Xerox 4450 Forms Creation Manual preview
4450
Brand: Xerox Pages: 108
Dascom TALLY MIP480 User Manual preview
TALLY MIP480
Brand: Dascom Pages: 138
Dascom T2150 User Manual preview
T2150
Brand: Dascom Pages: 166
Oki ML280 Elite Parts List preview
ML280 Elite
Brand: Oki Pages: 6
Oki ML1120 Safety & Warranty preview
ML1120
Brand: Oki Pages: 32
Oki ML1120 User Manual preview
ML1120
Brand: Oki Pages: 52
Oki ML520n Guía Del Usuario preview
ML520n
Brand: Oki Pages: 64
Oki ML520 Service Manual preview
ML520
Brand: Oki Pages: 269
Oki C9200 Replacement Manual preview
C9200
Brand: Oki Pages: 2
Oki C9200 Setup Manual preview
C9200
Brand: Oki Pages: 32
Oki C9200 Parts List preview
C9200
Brand: Oki Pages: 33
Oki B721dn Instructions Manual preview
B721dn
Brand: Oki Pages: 8
Oki ML690 Manual De L'Utilisateur preview
ML690
Brand: Oki Pages: 101
Oki ML690 Guía Del Usuario preview
ML690
Brand: Oki Pages: 104
Oki ML690 User Manual preview
ML690
Brand: Oki Pages: 99
Oki ML620 Manual Do Usuário preview
ML620
Brand: Oki Pages: 112
Oki ML620 User Manual preview
ML620
Brand: Oki Pages: 100

Brands by name

Popular brands

Load more brands