manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-4-4

Paper 
feed
section

19
Misfeed in paper feeder 
vertical paper convey-
ing section

The feed switch 3 (FSW3) does not turn off within speci-
fied time of its turning on (paper feed from optional cas-
sette 3).

1429 ms + Paper 
length

Feed switch 3 (FSW3) does not turn off within specified 
time of the paper feeder feed switch (PFFSW) turning on 
(paper feed from optional cassette 4).

1064 ms

The feed switch 3 (FSW3) does not turn off within speci-
fied time of its turning on (paper feed from optional cas-
sette 4).

1064 ms

Feed switch 3 (FSW3) does not turn on within specified 
time of the paper feeder feed switch (PFFSW) turning on 
(paper feed from optional cassette 4).

2000 ms

20
Misfeed in MP tray 
paper conveying sec-
tion

The registration switch (RSW) does not turn off within 
specified time of the MP feed switch (MPFSW) turning 
on.

1686 ms

The registration switch (RSW) does not turn on within 
specified time of the MP feed switch (MPFSW) turning 
on.

1686 ms

21
Multiple sheets in paper 
feed section

The feed switch 1 (FSW1) does not turn off within speci-
fied time of its turning on (paper feed from cassette 1).

1429 ms + Paper 
length

The feed switch 2 (FSW2) does not turn off within speci-
fied time of its turning on (paper feed from cassette 2).

1429 ms + Paper 
length

The feed switch 3 (FSW3) does not turn off within speci-
fied time of its turning on (paper feed from optional cas-
sette 3, 4/detected by the machine).

1429 ms + Paper 
length

The feed switch 3 (FSW3) does not turn off within speci-
fied time of its turning on (paper feed from optional cas-
sette 3, 4/detected by the paper feeder).

4300 ms

The feed switch 2 (FSW2) does not turn off within speci-
fied time of its turning on (paper feed from optional cas-
sette 3).

1686 ms

The paper feeder feed switch (PFFSW) does not turn off 
within specified time of its turning on (paper feed from 
optional cassette 4).

4300 ms

The feed switch 1 (FSW1) does not turn off within speci-
fied time of the upper paper feed clutch (PFCL-U) turning 
on.

1864 ms

The feed switch 2 (FSW2) does not turn off within speci-
fied time of the lower paper feed clutch (PFCL-L) turning 
on.

2121 ms

The feed switch 3 (FSW3) does not turn off within speci-
fied time of the paper feeder paper feed clutch 1 
(PFPFCL1) turning on.

2036 ms

23
Multiple sheets in MP 
tray conveying section

The MP feed switch (MPFSW) does not turn off within 
specified time of its turning on.

1429 ms + Paper 
length

Section

Description

Conditions

Specified time

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Samsung CJX-1050W Quick Install Manual preview
CJX-1050W
Brand: Samsung Pages: 2
TallyGenicom 6300 Series Maintenance Manual preview
6300 Series
Brand: TallyGenicom Pages: 175
Partner RP-330 Technical Manual preview
RP-330
Brand: Partner Pages: 81
POS-TECHNOLOGY PT80USEWB User Manual preview
PT80USEWB
Brand: POS-TECHNOLOGY Pages: 40
Mitsubishi TDP-459 User Manual preview
TDP-459
Brand: Mitsubishi Pages: 86
Gerber SOLARA UV2 Owner'S Manual preview
SOLARA UV2
Brand: Gerber Pages: 163
SPRT SP-RMT12 User Manual preview
SP-RMT12
Brand: SPRT Pages: 14
Fuji Xerox ApeosPort-IV C5580 Administrator'S Manual preview
ApeosPort-IV C5580
Brand: Fuji Xerox Pages: 739
DURACARD ID 300 User Manual preview
ID 300
Brand: DURACARD Pages: 31
Wang 1111M Maintenance Manual preview
1111M
Brand: Wang Pages: 39
Sony UP-20 Specifications preview
UP-20
Brand: Sony Pages: 2
Sony DPP-M55 Marketing Operating Instructions Manual preview
DPP-M55 Marketing
Brand: Sony Pages: 47
EFI VUTEk 3r Series Maintenance Manual preview
VUTEk 3r Series
Brand: EFI Pages: 69
Xerox WorkCentre 3655i Setup Instructions preview
WorkCentre 3655i
Brand: Xerox Pages: 20
MIMAKI JV300-130/160 Print Manual preview
JV300-130/160
Brand: MIMAKI Pages: 12
Lexmark Optra T Service Manual preview
Optra T
Brand: Lexmark Pages: 188
Lexmark Optra M410 Service Manual preview
Optra M410
Brand: Lexmark Pages: 195
MIMAKI JV33-130BS Operation Manual preview
JV33-130BS
Brand: MIMAKI Pages: 206

Brands by name

Popular brands

Load more brands