Kyocera KM-2560 Service Manual Download | Manualshive

Page: 62 / 392

background image

2H0/2HZ

1-3-26

U061

Turning the exposure lamp on
Description

Turns the exposure lamp on.

Purpose

To check the exposure lamp.

Method

1. Press the start key.
2. Select [CCD].
3. Press the start key. The exposure lamp lights.
4. To turn the exposure lamp off, press the stop key.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U063

Adjusting the shading position
Description

Changes the shading position of the scanner.

Purpose

Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned. This
is due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be
changed so that shading is possible without being affected by the flaws or stains.

Method

1. Press the start key.
2. Change the setting using the +/- or numeric keys.

Increasing the setting moves the shading position toward the machine left, and decreasing it moves the
position toward the machine right.

3. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the system menu key).

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Description

Setting range

Initial setting

Change in value per step

Shading position

-12 to 18

0

0.086 mm

«
...
60
61
62
63
64
...
»

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Brand: Samsung Pages: 224

MF5750 - ImageCLASS B/W Laser

Brand: Canon Pages: 42

Brand: Canon Pages: 394

Brand: Xerox Pages: 200

Brand: Oki Pages: 156

Brand: Xerox Pages: 29

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: Microcom Pages: 207

Brand: Xerox Pages: 284

Brand: Citizen Pages: 32

Brand: Digi Pages: 136

Brand: Cisco Pages: 43

VIP-5000 Series

Brand: Daktronics Pages: 62

Brand: Oki Pages: 6

Brand: OmniPrint Pages: 71

Brand: Sharp Pages: 168

Brand: Star Micronics Pages: 1

Brand: Star Micronics Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands