manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-3-44

U117

Checking the drum number
Description

Displays the drum number.

Purpose

To check the drum number.

Method

Press the start key. The drum number is displayed.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U118

Displaying the drum history
Description

Displays the past record of machine number and the drum counter.

Purpose

To check the count value of machine number and the drum counter.

Method

Press the start key. Past record of 5 cases is displayed.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U130

Initial setting for the developing unit
Description

Replenishes toner to the developing unit to a certain level from the toner container that has been installed.

Purpose

To operate when installing the machine or replacing the developing unit.

Method

1. Press the start key. The screen for executing is displayed.
2. Press the start key.

Toner installation is started and the output value of the sensor and execution time are displayed.

Completion

Press the stop key after initial setting is complete. The screen for selecting a maintenance item No. is dis-
played.

Maintenance

item No.

Description

Display

Description

MACHINE No.1 to 5

Past record of machine number

COUNT 1 to 5

Past record of drum counter

Display

Description

TONER SENSOR

Output value of the sensor

TIME(SEC)

Execution time

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Canon FaxPhone L120 Starter Manual preview
FaxPhone L120
Brand: Canon Pages: 11
Canon imageRUNNER ADVANCE 8085 Maintenance Manual preview
imageRUNNER ADVANCE 8085
Brand: Canon Pages: 176
Canon FaxPhone L120 Software Manual preview
FaxPhone L120
Brand: Canon Pages: 85
Canon imageRUNNER 5070 Specification preview
imageRUNNER 5070
Brand: Canon Pages: 4
Canon imageRUNNER 5570 Specification preview
imageRUNNER 5570
Brand: Canon Pages: 4
Canon IMAGERUNNER 7095 PRINTER Brochure & Specs preview
IMAGERUNNER 7095 PRINTER
Brand: Canon Pages: 8
Canon IMAGERUNNER 7105 Service Manual preview
IMAGERUNNER 7105
Brand: Canon Pages: 21
Canon FaxPhone L120 Advanced Manual preview
FaxPhone L120
Brand: Canon Pages: 58
Canon IMAGERUNNER ADVANCE C5051 Manual preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 12
Canon imageRUNNER ADVANCE C2020 Setup Manual preview
imageRUNNER ADVANCE C2020
Brand: Canon Pages: 68
Canon imageRUNNER ADVANCE 6055 Maintenance Manual preview
imageRUNNER ADVANCE 6055
Brand: Canon Pages: 134
Canon Color imageRUNNER LBP5970 Getting Started Manual preview
Color imageRUNNER LBP5970
Brand: Canon Pages: 67
Canon FAXPHONE L170 - B/W Laser - Copier Starter Manual preview
FAXPHONE L170 - B/W Laser - Copier
Brand: Canon Pages: 12
Canon FAXPHONE L100 Technical Information preview
FAXPHONE L100
Brand: Canon Pages: 2
Canon imageRunner 1133 Starter Manual preview
imageRunner 1133
Brand: Canon Pages: 60
Canon Color imageCLASS MF8280Cw Getting Started Manual preview
Color imageCLASS MF8280Cw
Brand: Canon Pages: 36
Canon FAX-L380 Software Manual preview
FAX-L380
Brand: Canon Pages: 104
Canon imagePROGRAF iPF8300 Setup Manual preview
imagePROGRAF iPF8300
Brand: Canon Pages: 16

Brands by name

Popular brands

Load more brands