manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-3-86

Zoom

Select the enlarged/reduced default when paper size/
sending size changed after the originals set.

1. Press [Next] of Function Defaults and then 

[Change] of Zoom.

2. Press [100%] or [Auto].
3. Press [OK].

File name entry

Set an automatically entered name (default) for jobs. 
Additional information such as Date and Time and Job 
No. can also be set.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of File Name Entry.

2. Press [File Name] to enter the file name in not more 

than 30 characters.

3. Press [OK].
4. Press [Date and Time] to add the date/time to the 

job, or press [Job No.] to add the job number to the 
job. The added information will be displayed in 
Additional Info..

5. Press [OK].

E-mail subject/body

Set the subject and body automatically entered (default 
subject and body) when sending the scanned originals by 
E-mail.

1. Press [Next] of Function Defaults, cursor down key, 

and then [Change] of E-mail Subject/Body.

2. Press [Subject] to enter an E-mail subject not more 

than 60 characters.

3. Press [OK].
4. Press [Body] to enter an E-mail body not more than 

500 characters.

5. Press [OK].
6. Check if the entries are correct and press [OK].

Border erase default

Set the default border width to be erased.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of Border Erase Default.

2. Press [+] or [-] for the Border and Gutter width to 

erase.

3. Press [OK].

Margin default

Set the default margin.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of Margin Default.

2. Press [+] or [-] for the Left/Right and Top/Bottom 

width margin.)

3. Press [OK].

Collate/Offset

Set the defaults for Collate/Offset.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of Collate/Offset.

2. Select the defaults.
3. Press [OK].

Auto image rotation

Select the default Auto Image Rotation setting.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of Auto Image Rotation.

2. Press [Off] or [On].
3. Press [OK].

Form overlay (copy)

Select the default form and form density from Form Box 
for form overlay for copy jobs.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of Form Overlay (Copy).

2. Press [Select Stored From].
3. Press [+] or [-] to enter the form density.
4. Press [Select Form].
5. Select the form and press [OK].
6. Press [OK].

Form overlay (box)

Select the default form and form density from Custom 
Box for form overlay for box print jobs.

1. Press [Next] of Function Defaults, cursor down key 

and [Change] of Form Overlay (Box).

2. Press [Select Stored From].
3. Press [+] or [-] to enter the form density.
4. Press [Select Form].
5. Select the Box where the Form is stored and press 

[Open].

6. Select the form and press [OK].
7. Press [OK].

EcoPrint

Select the EcoPrint default.

1. Press [Next] of Function Defaults, cursor down key 

and then [Change] of EcoPrint.

2. Press [Off] or [On].
3. Press [OK].

PDF/TIFF/JPEG image

Select the default PDF/TIFF/JPEG file quality.

1. Press [Next] of Function Defaults.

Press cursor down key twice and then [Change] of 
PDF/TIFF/JPEG Image.

2. Select the default image quality from [1 Low Quality 

(High Comp.) to [5 High Quality (Low Comp.)].

3. Press [OK].

High Comp. PDF image

Select the default High Comp.

1. Press [Next] of Function Defaults.

Press cursor down key twice and [Change] of High 
Comp. PDF Image.

2. Select the default for [Compression Ratio Priority], 

[Standard], or [Quality Priority].

3. Press [OK].

Repeat copying

Select the repeat copy default.

1. Press [Next] of Function Defaults.

Press cursor down key twice and [Change] of 
Repeat Copy.

2. Press [Off] or [On].
3. Press [OK].

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Labau TM200 User Manual preview
TM200
Brand: Labau Pages: 19
QMS Magicolor 2 Desklaser Install Manual preview
Magicolor 2 Desklaser
Brand: QMS Pages: 60
Xerox PHASER 6121MFP Service Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 532
Xerox Phaser 6120 User Manual preview
Phaser 6120
Brand: Xerox Pages: 174
Xerox Phaser 6115 MFP Repacking Manual preview
Phaser 6115 MFP
Brand: Xerox Pages: 2
Xerox Phaser 6115 MFP User Manual preview
Phaser 6115 MFP
Brand: Xerox Pages: 219
Xerox PHASER 6010 Quick Use Manual preview
PHASER 6010
Brand: Xerox Pages: 5
Xerox Phaser 6140N Product Safety Data Sheet preview
Phaser 6140N
Brand: Xerox Pages: 3
Xerox Phaser 6128 MFP Installation Manual preview
Phaser 6128 MFP
Brand: Xerox Pages: 2
Xerox Phaser 6128 MFP Evaluator Manual preview
Phaser 6128 MFP
Brand: Xerox Pages: 16
Xerox Phaser 6125 Specifications preview
Phaser 6125
Brand: Xerox Pages: 2
Xerox Phaser 7800 Training preview
Phaser 7800
Brand: Xerox Pages: 9
Xerox Phaser 7800 Quick Manual preview
Phaser 7800
Brand: Xerox Pages: 12
Xerox Phaser 7750 Adding Memory Manual preview
Phaser 7750
Brand: Xerox Pages: 2
Xerox Phaser 7750 Setup Manual preview
Phaser 7750
Brand: Xerox Pages: 2
Xerox Phaser 8500 Quick Manual preview
Phaser 8500
Brand: Xerox Pages: 4
Xerox Phaser 8500 Detailed Specifications preview
Phaser 8500
Brand: Xerox Pages: 4
Xerox Phaser 6500 User Manual preview
Phaser 6500
Brand: Xerox Pages: 162

Brands by name

Popular brands

Load more brands